Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Lakewood?
Gate access control in Lakewood typically runs $450 to $1,800 for a residential keypad, card reader, or intercom setup installed on an existing operator, and $1,200 to $3,500 when the work includes new wiring runs, a replacement control board, or a commercial-grade DoorKing or FAAC entry system. A simple keypad swap on a Mighty Mule or Ghost Controls opener often lands near the low end. A multi-unit property manager adding telephone entry and vehicle sensors should plan for the upper range. Every price we quote is an estimate, set per job by a written estimate after we look at the gate, the operator, and the wiring.
Gate Access Control Cost Breakdown (2026)
Here’s how the line items usually break out in the Lakewood market. These are typical ranges, not a quote. The written estimate is what sets the final number.
| Item | Typical Range | Notes |
|---|---|---|
| Keypad replacement (residential) | $180 – $420 | Wiring reuse keeps this near the bottom; new wire runs push it up |
| Wireless keypad or remote receiver add-on | $150 – $350 | Common on Mighty Mule and Ghost Controls residential operators |
| Control board replacement | $280 – $650 | Board + labor; brand and board availability drive the spread |
| Safety sensor pair (photo-eye or loop) | $220 – $520 | Loop installation costs more because it means cutting and sealing pavement |
| Intercom / telephone entry (residential) | $450 – $1,100 | DoorKing and Linear units sit in this band |
| Card reader or fob system | $600 – $1,600 | Reader, controller, and credential programming |
| Commercial telephone entry (multi-unit) | $1,400 – $3,500 | DoorKing systems on apartment and HOA gates |
| New low-voltage wiring run | $8 – $18 per foot | Burial, conduit, and trenching distance all matter |
| Full operator + access control install | $2,400 – $6,500 | Slide or swing operator plus entry hardware and sensors |
What moves the number up or down is mostly the wiring. Access control lives or dies on the low-voltage run between the entry device, the operator, and the power source. If the existing wire is sound, a keypad or reader swap is a short job. If the run is corroded, undersized, or was never buried in conduit, we’re trenching, and that’s where a $400 job becomes a $1,200 job. Brand matters too: a FAAC or BFT commercial operator usually has a cleaner control board interface than an older mass-market unit, which can shorten labor. A DoorKing telephone entry system on a property with multiple buildings needs more programming and testing than a single-family gate, and that time is real.
We work on nine brands and see this pattern across all of them: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Whether it’s a Mighty Mule on a residential driveway or a DoorKing at a Lakewood apartment entrance, the access control layer is where most of the cost variance hides.
What Affects Gate Access Control Pricing in Lakewood
- Wiring condition and distance. A short, dry, conduit-protected run keeps labor low. A long unburied run across a driveway or through landscaping means trenching, and trenching is priced by the foot. Lakewood’s clay-heavy soil and freeze-thaw cycles can shift buried runs over time, so a repair often starts with tracing the wire, not replacing the keypad.
- Operator brand and age. Control boards on a FAAC or BFT commercial operator are generally easier to interface with a new reader than an older board with proprietary terminal logic. A Mighty Mule or Ghost Controls residential operator usually accepts a standard keypad or receiver without much fuss. Linears and Elites land somewhere in the middle depending on the model year.
- Entry device type. A keypad is the cheapest entry point. A card reader or fob system costs more because it adds a controller and credential programming. Telephone entry, common on property-manager gates, is the priciest tier because it includes a directory, a phone line or cellular module, and multi-unit wiring.
- Property type. A single-family home in Belmar or Green Mountain needs one entry point. A multi-unit property or an HOA gate off Alameda Parkway may need vehicle loops, multiple readers, and a call box that reaches every unit. Scope scales directly with the number of entry points.
- Safety hardware. Photo-eye sensors and reversing edges are part of the access control layer, not an add-on. Most jurisdictions treat missing safety devices as a code issue, so we check and price them as part of the job. If your gate doesn’t have them, that’s a required line item, not an upsell.
- Panel and power access. The operator’s low-voltage control wiring is safe to trace, but anything that touches line voltage at the power source is a job for a trained electrician. If the access control point needs a new power drop, that’s a separate licensed trade and it’s priced accordingly.
How to Save on Gate Access Control
The biggest savings come from fixing the wiring before it fails. If your keypad works only when it’s dry out, or your reader drops a credential now and then, that’s a failing connection, not a failing device. Replacing a $300 keypad when the real problem is a $60 splice in a wet junction box is the most common waste we see. Call us and describe the symptom; we can usually narrow it down over the phone before anyone drives out.
A few other practical ways to keep the cost down:
- Keep the operator, upgrade the entry. If the motor is healthy and only the access control is tired, a keypad or receiver swap is far cheaper than a full operator replacement. A brand-literate technician can tell the difference in a few minutes.
- Match the entry device to how the property is actually used. A single-family home doesn’t need a card reader system. A multi-unit property shouldn’t be running on a shared keypad code. Matching the hardware to the traffic pattern avoids paying for capability you won’t use.
- Bundle open items into one visit. If the safety sensors are loose and the keypad is intermittent, price both in the same written estimate. One trip, one reset, one test.
- Replace only what failed. We test the board, the wiring, the entry device, and the sensors separately, and we tell you which ones are actually bad. Replacing all four because one is bad is a bigger bill for no reason.
- Ask for a written estimate before work starts. The estimate is free, up front, and per job. That’s the number you can hold us to.
If you’re comparing options, call (866) 330-9331 and we’ll walk through what usually fails on your specific brand. We answer 24/7.
FAQs – Gate Access Control Cost
How much does a keypad replacement cost in Lakewood?
A residential keypad replacement typically runs $180 to $420. If the existing low-voltage wiring is sound, the job is short. If the wire is damaged or wasn’t buried in conduit, expect the upper end or above, because we’re tracing and possibly replacing the run. The written estimate sets the price. Call (866) 330-9331 for an exact quote; estimates are free.
How much does it cost to add card reader or telephone entry access?
Card reader and fob systems typically run $600 to $1,600. Telephone entry systems on residential gates run $450 to $1,100, and commercial multi-unit telephone entry systems (common on DoorKing setups at Lakewood apartment complexes and HOA gates) run $1,400 to $3,500. The spread comes from the number of entry points, credential programming, and wiring distance. Call for a free estimate tailored to your property.
Can I just replace the keypad myself to save money?
Sometimes yes, on a residential operator where the existing keypad uses standard terminals and the wiring is intact. On anything with a control board interface, a DoorKing or FAAC commercial unit, or a gate where the access point ties into safety sensors, a wrong connection can lock out the operator or bypass the reversing device. Access control terminals are low voltage, but the boards are easy to short and the safety circuit is not something to disable. We’re happy to quote the swap if you’d rather not risk it.
Why did my access control price come in higher than the typical range?
Usually wiring. Trenching a new low-voltage run, adding conduit, replacing a buried loop, or bringing a new power drop to the access point can push the total beyond the typical band. Multi-unit properties and gates with no existing safety sensors also land above the range, because those items are required parts of the job. A free on-site estimate gives you the exact number. Call (866) 330-9331.
Is it cheaper to repair my existing access control or replace the whole system?
Repair is cheaper when the operator is healthy and only the access control layer has failed. A keypad or control board repair typically runs $180 to $650. A full operator and access control replacement runs $2,400 to $6,500. The dividing line is the operator’s motor and mechanism; if those are sound, repair wins almost every time. We test both and tell you which side of the line you’re on. Call (866) 330-9331 for a free written estimate.
Safety Notes on Gate Access Control Wiring
Access control devices themselves run on low voltage, and the wiring between the keypad, the reader, or the telephone entry unit and the control board is generally safe to inspect visually. The dangerous part of any gate is the operator’s high-voltage power supply and the heavy moving panel. A gate operator holds stored energy, and a panel that moves unexpectedly can crush a hand, a pet, or a child. We don’t walk homeowners through connections at the control board, and we don’t disable safety sensors to make a keypad “just work.” If your gate has no photo-eye or reversing edge, get it looked at before anything else. We answer 24/7 at (866) 330-9331, and fast dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday; a call that comes in on Saturday gets booked into the next opening.
Why a Gate Specialist Prices This Differently
A general handyman will look at a dead keypad, call it a keypad problem, and swap the keypad. A dedicated gate technician looks at the same symptom and starts at the control board, because on a LiftMaster or Elite operator the symptom usually points upstream. That distinction matters on a pricing page: the cheaper diagnosis is often the more expensive repair, because it replaces a good part. Electric gate repair is what we do, from the motor to the hinge, and access control is part of that whole-system picture, not a separate trade we hand off.
Our technicians have up to 12 years of experience, and every job we run is a gate job. That pattern recognition is why we can often tell you on the phone whether you’re looking at a $200 keypad fix or a $900 wiring problem before anyone drives out. We’re fluent in nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Residential systems and professional-grade commercial operators sit in the same service roster.
We also cover installation, so you’re not hunting for a second contractor when your needs grow from a keypad on a driveway gate to a fob system at a multi-unit entry. From first install through long-term maintenance, it’s one call. If you want the broader picture of how we work in this market, start with Lakewood. If you’re looking for a gate specialist for your property, Lakewood Gate Repair is the place to begin.
When to Call for a Quote
Call when the keypad works only sometimes. Call when a credential stops working. Call when the gate opens for one car and closes on the next. Call when you’re adding access control to a gate that never had it. Call when an HOA board or a tenant is asking why the entry system keeps failing. Each of those is a job we price with a free written estimate, and each one has a typical range on this page so you can budget before you call.
One more thing on estimates: the price is set per job, after we look at the gate. We don’t quote over the phone as a final number because the wiring, the operator, and the entry device all have to line up first. The free on-site estimate is the number you can trust. Call (866) 330-9331 to set it up. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Lakewood market as of 2026. Lakewood Gate Repair offers free estimates – call (866) 330-9331.
Written by the team at Lakewood Gate Repair.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Dale Padgett"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Nicole Schaefer"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Kristen Hayes