Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Lakewood?
Gate parts and welding in Lakewood typically cost $150 to $1,800 depending on what’s needed, with most single-part repairs landing between $180 and $450 and on-site welding running $150 to $400. A hinge set replacement is often $180 – $320, an operator control board runs $250 – $550, and a full swing-gate weld repair with re-hanging comes closer to $600 – $1,800. Every price is set per job by a written estimate, and estimates are free.
We’re Lakewood Gate Repair, a dedicated gate specialist. We don’t do garage doors, fencing, or general contracting – only gates, only gate parts, and only welding on gate systems. That narrow focus is why we can look at a sagging Mighty Mule or a failing DoorKing operator and know the fix before we load a tool. Our technicians have up to 12 years of experience, and we work on your brand: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Call (866) 330-9331 for an exact quote. We answer 24/7. Fast dispatch from 7am to 7pm.
Key Takeaways
- Most gate parts replacements in Lakewood run $150 – $550 for a single part; multi-part or heavy-panel welding jobs run $400 – $1,800.
- On-site aluminum or steel welding on a gate frame typically costs $150 – $400 for a standard job.
- Operator parts (motors, control boards, safety sensors) are the biggest cost swing – a Ghost Controls board and a FAAC motor aren’t the same price.
- Replacing gate hardware early is usually cheaper than repairing a collapsed frame later.
- Estimates are free, and the written estimate sets the final price.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the main pieces of a gate parts or welding job typically cost in the Lakewood market. These ranges are for the work and the parts together unless noted; your written estimate sets the final number for your specific gate.
| Work / Part | Typical Lakewood Range | Notes |
|---|---|---|
| Hinge replacement (hinge set, re-hang) | $180 – $320 | Swing gates; includes shimming and alignment |
| Latch, striker, and closer hardware | $150 – $280 | Single-point jobs; multi-point costs more |
| Roller and track hardware (slide gates) | $180 – $350 | Roller re-set plus track shim |
| Weld repair on gate frame (steel or aluminum) | $150 – $400 | Standard on-site weld; heavy panel re-weld toward the top |
| Post weld and footing re-set advice | $300 – $700 | Only after we assess the footing depth |
| Gate operator motor (residential class) | $400 – $900 | Mighty Mule or Ghost Controls-type replacements |
| Gate operator motor (professional tier) | $650 – $1,500 | FAAC, BFT, LiftMaster, DoorKing-type units |
| Control board replacement | $250 – $550 | Part price varies by brand |
| Safety sensor / photo-eye pair | $180 – $380 | Wired; extra runs cost more |
| Wiring, conduit, and low-voltage run | $200 – $650 | Depends on run length and trench situation |
| Full parts-and-weld repair (frame + hardware + operator part) | $600 – $1,800 | Whole-system job; the written estimate guarantees the number |
What pushes a job up or down? Mostly three things: the brand tier of the operator, whether welding is needed on a heavy panel or just on thin ornament, and how much is already failing when we arrive. A residential Mighty Mule control board is a very different line item from a commercial DoorKing board. A BFT or FAAC motor swap runs toward the top of the motor range because the hardware itself costs more. And steel-frame weld repair on a sliding gate that’s come off the track adds labor because the panel has to be safely supported before anyone touches their torch. We never quote over the phone without seeing the gate; the estimate is where the number is fixed.
What Affects Gate Parts & Welding Pricing in Lakewood
- Brand and tier. Consumer gates (Mighty Mule, Ghost Controls) often use parts that cost less, while professional-tier systems (FAAC, BFT, DoorKing, LiftMaster) carry higher part prices. We stock nothing on a truck; we source per job, and the written estimate reflects the actual part cost.
- Manual vs. electric. Welding on a manual swing gate is largely labor only. On an electric gate, the same weld often brings wiring, a safety sensor, and an operator re-check into the job.
- Gate weight and panel size. A heavy steel slide gate needs more support, more time, and sometimes a two-person lift during re-hang. Weight is one of the biggest swing factors in a weld quote.
- Type of damage. A single hinge that’s sheared is a small job. A frame that’s cracked at the weld seams because a footing has shifted, or a slide gate that’s come off the track and bent, is a larger one.
- Lakewood’s metro setting. Lakewood sits right against the Front Range foothills, and the seasonal ground movement along the west side of town is a routine reason we see posts and frames go out of alignment. When the footing is the root cause, the fix can involve more than a weld.
- Access and trenching. A gate on a slope, or over a driveway that needs a low-voltage conduit run, adds labor. Long runs to a driveway entry from the house or a post-mounted control are a common add-on.
How to Save on Gate Parts & Welding
Gate hardware rarely fails all at once. A hinge that’s loosened a little, a roller that’s grinding, a latch that’s catching – caught early, these are small welds and single-part replacements. Caught late, a loose hinge can drag the whole gate out of alignment, and a frame goes from a $180 fix to a $700 job. The cheapest move a Lakewood homeowner or property manager can make is to call when the gate starts acting differently, not when it stops working.
A few practical tips:
- Fix hardware before it cascades. A worn hinge stresses the frame, the operator, and the post. Replace the hinge first and you’ll often avoid three other problems.
- Ask about replacing like-for-like on parts. If the operator works and only the sensor failed, we don’t push a full motor replacement. We quote what the gate needs.
- Bundle the weld and the hardware. If a hinge and a weld are both failing on the same gate, doing them in one visit costs less than two dispatches.
- Note the brand before you call. If you know your operator is a Linear or a Viking, say so. Our technicians have up to 12 years of experience across all nine brands we service, and a quick brand confirmation shortens the estimate process.
- Get the free estimate. Call (866) 330-9331 and we’ll come look. Nothing is fixed until the written estimate is in your hands, and the estimate itself is free.
One thing we won’t do: quote a weld repair without looking at the gate. A steel frame that’s cracked at a seam looks like a $200 touch-up in a photo and turns out to be a re-hang once we see the footing. The estimate is where the number is real.
Can I weld a gate myself, or should I hire a gate specialist?
Hire a gate specialist for anything structural on a gate. Welding on a gate frame involves more than the weld itself: a heavy swing or slide panel has to be safely supported while the frame is worked on, and a slide gate that’s come off its track can crush a hand or worse if it shifts mid-repair. There’s also the operator wiring and the power feed to the gate motor, which are live-electrical territory. A trained gate technician works around both hazards every day. We recommend calling us rather than attempting a structural gate weld yourself. Call (866) 330-9331 for a free estimate.
Do I need to replace the whole gate or just the part?
In most cases, just the part. A hinge, a roller, a latch, a control board, a safety sensor, or a weld on the frame is a repair, not a replacement. Full gate replacement in Lakewood usually ranges from $1,800 to $6,500 on top of the parts cost, and the reason to go that way is structural failure, not routine wear. When we look at a gate we tell you plainly whether the part fix is worth it or whether the frame is too far gone. Call (866) 330-9331 – estimates are free.
How much does a control board replacement cost in Lakewood?
A gate operator control board replacement in Lakewood typically costs $250 – $550, depending on the brand of the operator. A Ghost Controls or Mighty Mule residential-class board usually sits toward the low end; a DoorKing, FAAC, or BFT professional board runs higher because the part itself costs more. The labor to swap and re-verify the safety sensors is included in the estimate. Call (866) 330-9331 for an exact quote – estimates are free.
How much does it cost to fix a slide gate that’s come off the track?
Re-setting a slide gate that’s come off the track typically costs $300 – $750 in Lakewood, and the number depends on whether the rollers, track, or post footing are the root cause. If the rollers are bent, they’re replaced; if the track has shifted, it’s shimmed; if the post has moved, the footing has to be assessed. Heavy slide panels are a two-technician job. Call (866) 330-9331 to set up an estimate – it’s free.
Can you give me a price over the phone?
We can give you a ballpark from the ranges above, but the firm price comes from a written estimate after we look at the gate. Gate jobs vary by brand, weight, and condition, and a phone estimate is a guess. The written estimate sets the final price, and it’s free. Call (866) 330-9331. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do you work on my gate brand?
Yes, if it’s one of these nine: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers everything from DIY-grade residential systems up to commercial-grade operators. If your gate is a brand outside that list, call us anyway and we’ll tell you honestly whether we can help. Call (866) 330-9331. We answer 24/7. Fast dispatch from 7am to 7pm.
Gate parts and welding in Lakewood don’t have to be a mystery. The ranges on this page cover most of what we see on a normal service day, and the written estimate is what fixes your number. What we do is gate parts, gate welding, gate repair, electric gate repair, and gate installation – nothing else. When the gate on a Mighty Mule operator, a FAAC swing, a DoorKing commercial slab, or a Ghost Controls driveway is acting up, call (866) 330-9331 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Lakewood market as of 2026. Lakewood Gate Repair offers free estimates – call (866) 330-9331.
Written by the team at Lakewood Gate Repair.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Dale Padgett"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Nicole Schaefer"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Kristen Hayes